Large American Flag Mold - 24x15x1" - USA Flag Silicone Mold
🚚 FREE SHIPPING. SHIPS WITHIN 2 DAYS.*
| Interior Size: | 24x15x1" |
| Fluid Volume: |
195oz / 5766 ml |
| Wall Thickness: | 5/8" |
| Material: | Platinum Cure Silicone - Shore 30A |
| Interior Finish: | Polished / Shiny |
That's a HUGE flag! We don't have to tell you that Americana always sells well, but our customers have told us that finding a large USA flag mold has been an impossibility. Not anymore!
Create beautiful and iconic American flags out of epoxy resin, Jesmonite, concrete or even chocolate using this oversized 24x15x1" silicone mold. This mold is designed with separation lines a little over 1/8" wide and 0.2" in depth between each bar of the flag representing the original 13 colonies. The 50 stars are nearly 1/4" in depth.
Creating a finished flag with this mold with multiple colors is a three step process. First fill each of the 13 bars up to 0.2" in depth, then fill the background section behind the stars. The colors are separated from mixing by the raised lines in the mold. After the initial pour has cured, backfill the entire flag with whatever color you chose (or clear resin) to effectively tie all of the components together. Though the mold is 1" deep, you can get away with as little as 1/2" total thickness if you wish to save resin and have a thinner flag. After the second layer has cured, demold the flag from the mold, then backfill the 50 stars with the appropriate color.
Crafted Elements Silicone Molds
The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:
- They can be used with epoxy resin, resin and wood, concrete, Jesmonite, plaster and more.
- They never need assembled, or disassembled. Saving huge amounts of time.
- The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
- The corners and edges never need sealed.
- When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Alternatively use our HDPE block kit in conjunction with hand weights or clamps to keep your wood from up in your resin. The HDPE blocks dont stick to set resin and are easily and cleanly removed.
- The mold is heat resistant to ~450F. Avoid direct contact with the flame of a torch. Briskly wave your torch or use a heat gun to pop bubbles.
- The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a non-silicone based mold release spray is used.
- Like HDPE, epoxy resin does not stick to silicone. However, the heat generated by the exothermic reaction and the chemicals in epoxy resin are very harsh to all silicone molds. Additionally, if part of your epoxy has not fully set due to improper mixing, the epoxy can become bonded to the mold. Both of these factors can lead to mold tear out when removing your piece from the mold, leading to pits and tears on the surface of the mold. This is why we a non-silicone based mold release spray is required before each pour. To help prevent tear out and to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', 'Mann Ease Release 200' or 'Mann Ease Release 300'. Cooking spray, vaseline, silicone based sprays or sprays designed for urethane or polyester products should NEVER be used. Using a proper, non-silicone based mold release can mean the difference between getting only a couple of uses from your mold to 20, 30 or more.
- Mold Instructions & Care - Click Here