Your cart
Close Alternative Icon
WE SHIP WORLDWIDE - FREE SHIPPING FOR ORDERS $100+ WITHIN THE USA & CANADA* WE SHIP WORLDWIDE - FREE SHIPPING FOR ORDERS $100+ WITHIN THE USA & CANADA*
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold
8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold

8x2" Round Deep Tray Silicone Mold For Epoxy Resin - 1" Deep Dish Mold

SKU CE-MOLD-SILIH-8X2-CYL-TRAY

$144.00

FREE SHIPPING

Interior Size: 8x2" (Dish 6x1")
Fluid Volume:
40oz / 1180ml
Wall Thickness: 1/2"
Material: Platinum Cure Silicone - Shore 30A
Interior Finish: Polished / Shiny

Our deep tray molds collection was born out of requests from our customers for a thick and durable mold that could be used to create things like cigar trays, rolling trays, coin dishes, small planters for succulents and more. Unlike typical small and thin silicone tray molds, these molds feature substantial 1" wide sidewalls that gives you the ability to integrate live edge wood, or encase small objects right within the side of the tray. The interior tray portion of the finished piece this mold makes is 6" in diameter and 1" deep, allowing it to be fully functional as a dish or tray.

Making a cigar or ashtray? Demold your piece then run rounded channels through the top of it using a router table and appropriate router bit.

Resin artists love these molds because small things can be encased within thick resin walls such as coins, dried flowers, coffee beans, sea shells, marbles, candy, and other knick-knacks that are less than 1" in size.

Note that due to the stiffness of the silicone, demolding a piece of this height can be challenging. There are two ways to remove castings from this mold as peeling back the mold significantly will likely result in tearing.

1. Pouring distilled water between the cured resin piece and the interior wall of the mold and moving the water around the resin casting before trying to attempt to remove it from the mold. 

2. Using a compressed air hose with a soft (plastic or rubber) gun nozzle end. Insert your air gun in between the casting and the mold wall and scale up the air flow rate until the casting rises from the mold.

Crafted Elements Silicone Molds

The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:

  • They can be used with epoxy resin, resin and wood, concrete, plaster and more.
  • They never need assembled, or disassembled. Saving huge amounts of time.
  • The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
  • The corners and edges never need sealed.
  • When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Preventing the need for clamps or weights.
  • The mold is heat resistant (within reason!), and wont damage when you are popping epoxy bubbles with a torch or heat gun.
  • The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a mold release spray is used.
  • Like HDPE, epoxy resin does not stick to silicone. However, the heat generated by the exothermic reaction and the chemicals in epoxy resin are very harsh to all silicone molds. Additionally, if part of your epoxy has not fully set due to improper mixing, the epoxy can become bonded to the mold. Both of these factors can lead to mold tear out when removing your piece from the mold, leading to pits and tears on the surface of the mold. This is why we strongly recommend the use of non-silicone based mold release spray before each pour to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', Smooth-On Ease Release 200 or Mann Ease Release 200 which are readily available from Amazon and other online retailers. Cooking spray, vaseline, silicone based sprays or sprays designed for urethane or polyester products should NEVER be used. Using a proper, non-silicone based mold release can mean the difference between getting only a couple of uses from your mold to 20, 30 or more.
  • Mold Instructions & Care - Click Here