Skip to content


22x8x1" Razor Charcuterie Board Silicone Mold With Handle - Serving Board Mold

Original price $99 USD - Original price $99 USD
Original price $99 USD
$99 USD
$99 USD - $99 USD
Current price $99 USD

🔗 There Is A Router Template To Match This Mold
Optional. Use Matching Template To Shape Wood To Fit Into This Mold
Interior Size: 21.5x8.5x1"
Fluid Volume:
56oz / 1656ml
Wall Thickness: 1/2"
Material: Platinum Cure Silicone - Shore 30A
Interior Finish: Polished / Shiny

We have specialized in high quality charcuterie board molds since mid-2019. The very first mold in our line was specific to creating serving boards. So, we are excited to introduce our new line of super thick, durable and deep silicone charcuterie board molds WITH handles!

The integrated handle shape makes creating high quality resin (or resin and wood) serving boards a breeze. No more cutting, forming, and routering handles after the fact and wasting material. You can now create solid resin handles right at the time of your pour. At 1" in depth, you can use this mold to create mixed media boards with wood and resin, or just pour up to 1/2" or 3/4" in height to make a thinner full-resin board.

This particular serving board mold features a modern, edgy design that can only be described as a mix between a straight razor, meat cleaver and an 80's punk rock guitar. Although the sides are straight, the angles of the walls creates a board that gets wider from the top to bottom. The handle is seamlessly integrated into one side as to not take away from the 'razor clean' lines of the piece. The size of the finished charcuterie board at the widest extents without the handle is approximately 17"x8", with the handle included the finished piece is 22" x 8", at up to 1" in depth (depending on the volume of your pour).

Crafted Elements Silicone Molds

The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:

  • They can be used with epoxy resin, resin and wood, concrete, Jesmonite, plaster and more.
  • They never need assembled, or disassembled. Saving huge amounts of time.
  • The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
  • The corners and edges never need sealed.
  • When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Alternatively use our HDPE block kit in conjunction with hand weights or clamps to keep your wood from up in your resin. The HDPE blocks dont stick to set resin and are easily and cleanly removed.
  • The mold is heat resistant to ~450F. Avoid direct contact with the flame of a torch. Briskly wave your torch or use a heat gun to pop bubbles.
  • The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a non-silicone based mold release spray is used.
  • Like HDPE, epoxy resin does not stick to silicone. However, the heat generated by the exothermic reaction and the chemicals in epoxy resin are very harsh to all silicone molds. Additionally, if part of your epoxy has not fully set due to improper mixing, the epoxy can become bonded to the mold. Both of these factors can lead to mold tear out when removing your piece from the mold, leading to pits and tears on the surface of the mold. This is why we a non-silicone based mold release spray is required before each pour. To help prevent tear out and to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', 'Mann Ease Release 200' or 'Mann Ease Release 300'. Cooking spray, vaseline, silicone based sprays or sprays designed for urethane or polyester products should NEVER be used. Using a proper, non-silicone based mold release can mean the difference between getting only a couple of uses from your mold to 20, 30 or more.
  • Mold Instructions & Care - Click Here