Your cart
Close Alternative Icon
WE SHIP WORLDWIDE - FREE SHIPPING FOR ORDERS $100 USD+ WITHIN THE USA & CANADA* WE SHIP WORLDWIDE - FREE SHIPPING FOR ORDERS $100 USD+ WITHIN THE USA & CANADA*
20% OFF ROUTER TEMPLATES. ENDS MARCH 3RD USE CODE: TEMP20
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold
22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold

22.5x20.5x1.5" Silicone Mold For Epoxy Resin - Small Table Top Mold

SKU CE-MOLD-SILIH-22.5X20.5X1.5

$321 USD


FREE SHIPPING. SHIPS WITHIN 2 BUSINESS DAYS.*

Interior Size: 22.5x20.5x1.5"
Fluid Volume:
383oz / 11337ml
Wall Thickness: 5/8"
Material: Platinum Cure Silicone - Shore 30A
Interior Finish: Polished / Shiny

The 22.5x20.5x1.5" silicone mold is an incredible mold for woodworkers, resin artists and and makers. This BIG mold allows you to create large resin works, or small side table tops up to 1.5" thick.

This mold can be used with various types of resin, concrete, and even mixed media such as a combination of live edge wood and resin. This size was in demand by our customers for quite some time, and we are pleased to finally release it to empower your creative endeavors!

IMPORTANT NOTES AND DISCLAIMER SPECIFIC TO OUR VERY LARGE SILICONE MOLDS:

These molds are made in-house using platinum cure silicone. However, due to the amount of silicone used and labor input to produce molds of this size and weight there are certain limitations and expectations that need to be clear before purchase. First, although we try to create perfect molds, pouring the volume of silicone required for this mold is a challenge.

Normally we would not allow a mold with micro surface bubbles or small inclusions (such as a tiny piece of plastic or dirt from the air in our shop) to pass as a "grade a" mold. However, pouring a mold this size and volume increases that risk notably and due to the cost of producing something this size we need to allow for a limited amount of imperfections. Thus, molds of this size with micro sized imperfections that won't have a notable effect on the final demolded product will still be considered "Grade A" saleable molds. Small micro bubbles within the mold walls or floor not on the surface can also be expected but are not considered "surface bubbles".

We would never ship a product that is ripped, torn or gouged, but again, due to the volume and facility conditions, perfection is hard to achieve over this much surface area.

BY PURCHASING THIS MOLD YOU UNDERSTAND AND AGREE TO THE CONDITIONS AND EXCEPTIONS TO OUR NORMAL POLICIES STATED ABOVE.

Crafted Elements Silicone Molds

The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:

  • They can be used with epoxy resin, resin and wood, concrete, Jesmonite, plaster and more.
  • They never need assembled, or disassembled. Saving huge amounts of time.
  • The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
  • The corners and edges never need sealed.
  • When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Alternatively use our HDPE block kit in conjunction with hand weights or clamps to keep your wood from up in your resin. The HDPE blocks dont stick to set resin and are easily and cleanly removed.
  • The mold is heat resistant to ~450F. Avoid direct contact with the flame of a torch. Briskly wave your torch or use a heat gun to pop bubbles.
  • The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a non-silicone based mold release spray is used.
  • Like HDPE, epoxy resin does not stick to silicone. However, the heat generated by the exothermic reaction and the chemicals in epoxy resin are very harsh to all silicone molds. Additionally, if part of your epoxy has not fully set due to improper mixing, the epoxy can become bonded to the mold. Both of these factors can lead to mold tear out when removing your piece from the mold, leading to pits and tears on the surface of the mold. This is why we a non-silicone based mold release spray is required before each pour. To help prevent tear out and to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', 'Mann Ease Release 200' or 'Mann Ease Release 300'. Cooking spray, vaseline, silicone based sprays or sprays designed for urethane or polyester products should NEVER be used. Using a proper, non-silicone based mold release can mean the difference between getting only a couple of uses from your mold to 20, 30 or more.
  • Mold Instructions & Care - Click Here