Your cart
Close Alternative Icon
WE SHIP WORLDWIDE - FREE GROUND SHIPPING WITHIN THE USA & CANADA* WE SHIP WORLDWIDE - FREE GROUND SHIPPING WITHIN THE USA & CANADA*
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin
12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin

12x6x0.75" Ankh Key Of Life Silicone Mold For Epoxy Resin

SKU CE-MOLD-SILIH-12X6X0.75-ANKH

$105.00
FREE SHIPPING


Interior Size: 11.75x6.25x3/4"
Fluid Volume:
11.8oz / 350ml
Wall Thickness: 1/2"
Material: Platinum Cure Silicone - Shore 30A
Interior Finish: Polished / Shiny

This approximately 12" high x 6" wide ankh Egyptian "key of life" mold is 3/4" deep. It can be used with wood and resin, concrete, plaster or solely resin. The ankh or key of life is an ancient Egyptian hieroglyphic symbol that was most commonly used in writing and in Egyptian art to represent the word for "life" and, by extension, as a symbol of life itself. The ankh has a cross shape but with a teardrop-shaped loop in place of a vertical upper bar.

This mold also features an integrated "sub-mold" within the main mold. The tear drop shape between the upper part of the ankh is also 3/4" deep, allowing the creation of small tear drop shaped pieces for jewelry and ornaments up to 3/4" thick.

Check out the YouTube video below to see the creation of a piece using the ankh "key of life" silicone mold from start to finish.

The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:

  • They can be used with epoxy resin, resin and wood, concrete, plaster and more.
  • They never need assembled, or disassembled. Saving huge amounts of time.
  • The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
  • The corners and edges never need sealed.
  • When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Preventing the need for clamps or weights.
  • The mold is heat resistant (within reason!), and wont damage when you are popping epoxy bubbles with a torch or heat gun.
  • The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a mold release spray is used.
  • Like HDPE, epoxy does not stick to silicone. However in rare cases where the epoxy hasn't fully set (and is still mildly tacky) it can be harder to remove, and potentially create pits or small tears inside the mold when your piece is pulled out. Thus, we recommend the use of mold release spray before each pour to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', or Smooth On Ease Release™ 200 which is readily available on Amazon.
  • Mold Instructions & Care - Click Here