16.5x4.5x1.0" Silicone Mold - Coaster / Cheeseboard Mold
SKU CE-MOLD-SIL-16.5X4.5X1
Sold out
🚚 SHIPS WITHIN 2 DAYS.*
Original price
$69 USD
-
Original price
$69 USD
Original price
$69 USD
$69 USD
$69 USD
-
$69 USD
Current price
$69 USD
🚚 SHIPS WITHIN 2 DAYS.*
| Interior Size: | 16.5x4.5x1.0" |
| Fluid Volume: |
41oz / 1212ml |
| Wall Thickness: | 1/2" |
| Material: | Silicone Rubber - Shore 40A |
| Interior Finish: | Polished / Shiny |
| Retail Packaging: |
Yes - Full Color |
The 16.5x4.5x1.0" silicone mold is the perfect mold for making small serving boards, cheese boards or sets of 4 coasters (after casting, trimming and planing you can cut your piece to the size of four 4x4" coasters).
This 1.0" deep version features a glossy (polished / shiny) interior to give your resin a polished look right out of the mold.
Crafted Elements Silicone Molds
The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:
- They can be used with epoxy resin, resin and wood, concrete, Jesmonite, plaster and more.
- They never need assembled, or disassembled. Saving huge amounts of time.
- The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
- The corners and edges never need sealed.
- When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Alternatively use our HDPE block kit in conjunction with hand weights or clamps to keep your wood from up in your resin. The HDPE blocks dont stick to set resin and are easily and cleanly removed.
- The mold is heat resistant to ~450F. Avoid direct contact with the flame of a torch. Briskly wave your torch or use a heat gun to pop bubbles.
- The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a non-silicone based mold release spray is used. The Mann Ease Release 300 and the MG Chemicals 8329 (Amazon) is what we most recommend.
- Like HDPE, epoxy resin does not stick to silicone. However, the heat generated by the exothermic reaction and the chemicals in epoxy resin are very harsh to all silicone molds. Additionally, if part of your epoxy has not fully set due to improper mixing, the epoxy can become bonded to the mold. Both of these factors can lead to mold tear out when removing your piece from the mold, leading to pits and tears on the surface of the mold. This is why we a non-silicone based mold release spray is required before each pour. To help prevent tear out and to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', 'Mann Ease Release 200' or 'Mann Ease Release 300'. Cooking spray, vaseline, silicone based sprays or sprays designed for urethane or polyester products should NEVER be used. Using a proper, non-silicone based mold release can mean the difference between getting only a couple of uses from your mold to 20, 30 or more.
- Mold Instructions & Care - Click Here