Skip to content


14x14x0.5" Medium Backgammon Board With Pieces Silicone Mold

Original price $131 USD - Original price $131 USD
Original price $131 USD
$131 USD
$131 USD - $131 USD
Current price $131 USD

Interior Size: 14x14x0.5" (Board). 0.875x0.375" (Pieces)
Fluid Volume:

Board Total = 48 oz / 1420ml
Each 'Stone' (1 Piece) = 0.13oz / 4ml
Total 'Stones' (30 Pieces) = 3.8oz / 113ml 
Grand Total = 51.8 oz / 1533ml

Wall Thickness: 1/2"
Material: Platinum Cure Silicone - Shore 30A
Interior Finish: Polished / Shiny

Looking for a high quality, durable and deep backgammon board mold? We have the answer! Create 14x14x1/2" boards and 30 pieces (aka. stones) in one go with the Medium Backgammon Board silicone mold by Crafted Elements.

As a game almost as popular as chess it made perfect sense for us to create a backgammon board silicone mold as a companion product to our popular line of large chess board molds.

At nearly 5lbs in weight and crafted with platinum cure silicone right here in our magical production facility you know your getting a heavy duty, super thick and premium mold that Crafted Elements is known for.

The easiest way to produce finished game sets with this mold is to do it in two sessions. First, pour the game pieces (30 side circles) and the alternating color "triangles" in the middle of the board. You can also fill the border in during this first pour if you'd like a different border color than the base of the board. Let the resin setup enough so it wont mix when you add additional resin. Assuming the initial pour is set, fill in the backer (bottom of the board) by topping up the center of the mold with the color of your choice. 

Crafted Elements Silicone Molds

The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:

  • They can be used with epoxy resin, resin and wood, concrete, Jesmonite, plaster and more.
  • They never need assembled, or disassembled. Saving huge amounts of time.
  • The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
  • The corners and edges never need sealed.
  • When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Alternatively use our HDPE block kit in conjunction with hand weights or clamps to keep your wood from up in your resin. The HDPE blocks dont stick to set resin and are easily and cleanly removed.
  • The mold is heat resistant to ~450F. Avoid direct contact with the flame of a torch. Briskly wave your torch or use a heat gun to pop bubbles.
  • The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a non-silicone based mold release spray is used.
  • Like HDPE, epoxy resin does not stick to silicone. However, the heat generated by the exothermic reaction and the chemicals in epoxy resin are very harsh to all silicone molds. Additionally, if part of your epoxy has not fully set due to improper mixing, the epoxy can become bonded to the mold. Both of these factors can lead to mold tear out when removing your piece from the mold, leading to pits and tears on the surface of the mold. This is why we a non-silicone based mold release spray is required before each pour. To help prevent tear out and to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', 'Mann Ease Release 200' or 'Mann Ease Release 300'. Cooking spray, vaseline, silicone based sprays or sprays designed for urethane or polyester products should NEVER be used. Using a proper, non-silicone based mold release can mean the difference between getting only a couple of uses from your mold to 20, 30 or more.
  • Mold Instructions & Care - Click Here