Your cart
Close Alternative Icon
WE SHIP WORLDWIDE - FREE GROUND SHIPPING WITHIN THE USA & CANADA* WE SHIP WORLDWIDE - FREE GROUND SHIPPING WITHIN THE USA & CANADA*
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation
8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation

8x3" Cylinder Silicone Mold For Epoxy Resin - Woodturning & Flower Preservation

SKU CE-MOLD-SILIH-8X3-CYL

$135.00
FREE SHIPPING


Interior Size: 8x3"
Fluid Volume:
83oz / 2458ml
Wall Thickness: 5/8"
Material: Platinum Cure Silicone - Shore 30A
Interior Finish: Polished / Shiny

This 8" diameter x 3" high cylinder mold is great for creating resin encased sculptures, flower bouquet preservation, small lamps and more. Large enough to embed flowers, action figures, wood and other small items into resin up to 3" tall and 8" wide. 

This mold is also frequently used to create raw woodturning blanks. Resin casting wood, or other material within this round silicone mold creates a perfect round blank for mounting on your lathe for turning.

Note that due to the stiffness of the silicone, demolding a piece of this height can be challenging. There are two ways to remove castings from this mold as peeling back the mold significantly will likely result in tearing.

1. Pouring distilled water between the cured resin piece and the interior wall of the mold and moving the water around the resin casting before trying to attempt to remove it from the mold. 

2. Using a compressed air hose with a soft (plastic or rubber) gun nozzle end. Insert your air gun in between the casting and the mold wall and scale up the air flow rate until the casting rises from the mold.

The last mold you will ever need. Created just for makers, resin artists and wood workers, these time saving flexible yet durable silicone molds significantly cut down on the setup and demolding time usually involved with other molds. Silicone molds are superior to wood and tuck tape, and HDPE molds because:

  • They can be used with epoxy resin, resin and wood, concrete, plaster and more.
  • They never need assembled, or disassembled. Saving huge amounts of time.
  • The strength and flexibility of the molds allows you to insert and remove pieces of wood easily.
  • The corners and edges never need sealed.
  • When using wood, the wood stays in place, tight in the mold if you cut it 1/16" larger than the width of the mold. Preventing the need for clamps or weights.
  • The mold is heat resistant (within reason!), and wont damage when you are popping epoxy bubbles with a torch or heat gun.
  • The molds are reusable. However silicone molds do have a finite lifespan when used with epoxy resin, but getting 20-30+ castings out of the mold can be expected when they are properly cared for and a mold release spray is used.
  • Like HDPE, epoxy does not stick to silicone. However in rare cases where the epoxy hasn't fully set (and is still mildly tacky) it can be harder to remove, and potentially create pits or small tears inside the mold when your piece is pulled out. Thus, we recommend the use of mold release spray before each pour to increase the life of your mold. We use the 'MG Chemicals 8329 Non-Silicone Epoxy Mold Release', or Smooth On Ease Release™ 200 which is readily available on Amazon.
  • Mold Instructions & Care - Click Here